Irwin 10507267 Mortar Rake Starter Kit, 8mm

Product Information

It is possible to use both 26 mm and 60 mm XL rakes with the Termite attachment; on deep cuts, two stage cutting using 26 mm and 60 mm rakes successively, will ensure maximum dust control. I purchased both sizes and on some bricks both were too large to go between the bricks to remove old mortar. There is manufacturer warranty for this product which covers all manufacturing defects for the normal lifetime of the tool but does not cover wear and tear or damaged cause by misuse. Our fully trained technical team can support you with advice on setup, parts or repairs for electrical products.

For deep cuts, it is probably best to make the initial cut with the standard 26 mm long rake and follow up with the same diameter of XL rake. Second set arrived and they are fine in soft - medium mortar and I guess hard mortar does not normally need raking out anyway! Various combinations of diameter (6, 8, 10 or 12 mm) and cutter count (3, 4 or 6) are available - check availability using drop-down selector alongside. These European-manufactured tungsten carbide mortar rakes fit directly to the M14 spindle on 115 and 125 mm angle grinders. Nylon spacer rings compensate for the variations found across the range of compatible angle grinders.Single motor SV30 M Class Dust Extractor with electric filter shaker, auto-sensing power tool socket and accessories kit. This should permit faster removal and cause less stress on the angle grinder, in addition to ensuring maximum dust control and debris collection (see next question). mm diameter, in 26 and 60 mm lengths, the Termite Wall Chaser Rake, for angle grinders with M14 spindles, is suitable for use in aerated concrete - it is NOT suitable for use in traditional brick, block or concrete structures. It is less intrusive to surrounding brickwork and is a good alternative to working with demolition chisels or grinding discs, which can easily cause damage.

mm overall length tungsten carbide mortar rake in 8 and 10 mm diameters, with three 60 mm long cutting edges. To calculate the overall star rating and percentage breakdown by star, we don’t use a simple average. They are also ideal for the short perp joints on brickwork, where a circular blade will not reach adequate depth due to the limitations imposed by the bricks above and below. A deeper joint might be required for inserting strengthening bars or to remove the mortar around a brick that needed removing (albeit a 60 mm rake is slightly short of a typical brick joint depth). We offer the Termite angle grinder attachment which provides dust control / extraction in addition to a depth setting facility.Our mortar rakes comprise carbide tungsten cutting strips (we refer to them as ’cutters’) brazed onto a steel core, which is secured in a hex-shaped holder, having an internal M14 thread to match that of an angle grinder spindle. When coupled with a suitable dust extractor (vacuum unit) substantially dust free operation will be achieved and the waste debris will also be collected. Please include what you were doing when this page came up and the Cloudflare Ray ID found at the bottom of this page. By contrast, it is likely a 6 cutter rake will provide smoother operation on harder mortars, even though it may not cut any faster.

The rake is faster and less intrusive to surrounding brickwork and, unlike other methods, it is just as efficient for both horizontal and vertical joint clearing. Trading Depot advises strongly against booking Tradesmen until after goods are safely received and checked for this exact reason. The Irwin Mortar Cutter has been designed to use with the mortar rake kit to replace traditional methods of mortar removal such as powered mortar chisels and cutting discs.Superior design Mortar Raking attachment for small angle grinders combining dust and depth control functions. A brief look (circa 2019) at Tungsten Mortar Rakes and the relative performance of three, four and six blade examples.

We offer 6, 8, 10 and 12 mm diameter rakes, at a standard length of 26 mm, making them the obvious choice for raking out regular brick and stonework mortar joints.

If any of our products fall below the high standard you expect, we'll happily refund or exchange it within 14 days. Perfect for utilising an angle grinder to remove deteriorated mortar from between bricks in preparation for repointing. IRW10507267 Mortar Rake Starter Kit 8mmThe IRWIN carbide tipped mortar rake kit is a power tool accessory for the fast and efficient removal of mortar and cement joints in brickwork repointing applications and for chasing out channels for the installation of cable, pipes and switchboxes. All rakes are available with 3 cutters (‘cutters’ as explained in previous answer) with selected widths also available with 4 and 6 cutter configurations. uk/irwin-mortar-rakes-8mm-x-20-40mm-4-cutter-irw10507232 54467 IRWIN Mortar Rakes 8mm x 20/40mm 4 Cutter - IRW10507232 https://www.